Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM A1035/A1035M-13
Standard Specification for Deformed and Plain, Low-carbon, Chromium, Steel Bars for Concrete Reinforcement
STANDARD published on 1.4.2013
The information about the standard:
Designation standards: ASTM A1035/A1035M-13
Note: WITHDRAWN
Publication date standards: 1.4.2013
SKU: NS-1159
The number of pages: 6
Approximate weight : 18 g (0.04 lbs)
Country: American technical standard
Category: Technical standards ASTM
Annotation of standard text ASTM A1035/A1035M-13 :
Keywords:
concrete reinforcement, deformations (protrusions), low-carbon, chromium steel bars, ICS Number Code 77.140.15 (Steels for reinforcement of concrete)
Additional information
| 1. Scope | |||||||
|
1.1 This specification covers low-carbon, chromium, steel bars, deformed and plain for concrete reinforcement in cut lengths and coils. The standard sizes and dimensions of deformed bars and their number designations are given in Bar Designation |
Nominal Weight, lb/ft |
Nominal DimensionsA |
Deformation Requirements, in. [mm] |
||||
|
Diameter, |
Cross-Sectional |
Perimeter |
Maximum |
Minimum |
Maximum Gap |
||
|
3 [10] |
0.376 [ 0.560] |
0.375 [ 9.5] |
0.11 [ 71] |
1.178 [ 29.9] |
0.262 [ 6.7] |
0.015 [0.38] |
0.143 [ 3.6] |
|
4 [13] |
0.668 [ 0.994] |
0.500 [12.7] |
0.20 [ 129] |
1.571 [ 39.9] |
0.350 [ 8.9] |
0.020 [0.51] |
0.191 [ 4.9] |
|
5 [16] |
1.043 [ 1.552] |
0.625 [15.9] |
0.31 [ 199] |
1.963 [ 49.9] |
0.437 [11.1] |
0.028 [0.71] |
0.239 [ 6.1] |
|
6 [19] |
1.502 [ 2.235] |
0.750 [19.1] |
0.44 [ 284] |
2.356 [ 59.8] |
0.525 [13.3] |
0.038 [0.97] |
0.286 [ 7.3] |
|
7 [22] |
2.044 [ 3.042] |
0.875 [22.2] |
0.60 [ 387] |
2.749 [ 69.8] |
0.612 [15.5] |
0.044 [1.12] |
0.334 [ 8.5] |
|
8 [25] |
2.670 [ 3.973] |
1.000 [25.4] |
0.79 [ 510] |
3.142 [ 79.8] |
0.700 [17.8] |
0.050 [1.27] |
0.383 [ 9.7] |
|
9 [29] |
3.400 [ 5.060] |
1.128 [28.7] |
1.00 [ 645] |
3.544 [ 90.0] |
0.790 [20.1] |
0.056 [1.42] |
0.431 [10.9] |
|
10 [32] |
4.303 [ 6.404] |
1.270 [32.3] |
1.27 [ 819] |
3.990 [101.3] |
0.889 [22.6] |
0.064 [1.63] |
0.487 [12.4] |
|
11 [36] |
5.313 [ 7.907] |
1.410 [35.8] |
1.56 [1006] |
4.430 [112.5] |
0.987 [25.1] |
0.071 [1.80] |
0.540 [13.7] |
|
14 [43] |
7.65 [11.38 ] |
1.693 [43.0] |
2.25 [1452] |
5.32 [135.1] |
1.185 [30.1] |
0.085 [2.16] |
0.648 [16.5] |
|
18 [57] |
13.60 [20.24 ] |
2.257 [57.3] |
4.00 [2581] |
7.09 [180.1] |
1.58 [40.1] |
0.102 [2.59] |
0.864 [21.9] |
1.2 Bars are of two minimum yield
strength levels as defined in 9.2: namely, 100 000 psi [690 MPa], and
120 000 [830 MPa] designated as Grade 100 [690] and Grade 120
[830], respectively.
1.3 Deformed bars shall have a
minimum yield strength and other tensile properties in accordance
with
Grade 100 [690]
Grade 120 [830]
Tensile strength, min, psi [MPa]
150 000 [1030]
150 000 [1030]
Yield strength (0.2 % offset), min, psi [MPa]
100 000 [ 690]
120 000 [ 830]
Stress corresponding to an extension
under
load of 0.0035 in./in. [0.0035 mm/mm],
min, psi [MPa]
80 000 [ 550]
90 000 [ 620]
Elongation in 8 in. [200 mm], min, %:
Bar Designation No.
3 through 11 [10 through 36]
7
7
14, 18 [43, 57]
6
—
1.4 Requirements for alternate bar
sizes are presented in 1.5 This specification is applicable
for orders in either inch-pound units (as Specification A1035) or
in SI units (as Specification A1035M).
1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
|
Standard Test Methods for Bend Testing of Material for Ductility |
|
|
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
|
|
Standard Test Methods and Practices for Chemical Analysis of Steel Products |
|
|
Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
|
|
Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, and Alloy Steel |
|
|
Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
|
|
Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling (Includes all amendments and changes 4/27/2026). |
|
|
MIL-STD-129 |
Marking for Shipment and Storage |
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
