Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM C150/C150M-22
Standard Specification for Portland Cement
Translate name
STANDARD published on 1.7.2022
The information about the standard:
Designation standards: ASTM C150/C150M-22
Publication date standards: 1.7.2022
SKU: NS-1068713
The number of pages: 9
Approximate weight : 27 g (0.06 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM C150/C150M-22 :
This specification covers eight types of portland cement: type I, type IA, type II, type IIA, type III, type IIIA, type IV, and type V. The cement covered by this specification shall only contain the following ingredients: portland cement clinker; water or calcium sulfate, or both; limestone; processing additions; and air-entraining addition for air-entraining portland cement. Portland cement of each of the eight types must have the following chemical compositions: aluminum oxide, ferric oxide, magnesium oxide, sulfur trioxide, tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium aluminofernite. Applicable properties enumerated in this specification will be determined by the following test methods: air content of mortar, chemical analysis, strength, false set, fineness by air permeability, fineness by turbidimeter, heat of hydration, autoclave expansion, time of setting by gillmore needles, time of setting by vicat needles, sulfate resistance, calcium sulfate, and compressive strength. The cement shall be stored in such a manner as to permit easy access for proper inspection and identification of each shipment, and in a suitable weather-tight building that will protect the cement from dampness and minimize warehouse set.
Keywords:
hydraulic cement, portland cement, specification,, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Additional information
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers ten types of portland cement, as follows (see Note 2): 1.1.1?Type IFor general use, when the special properties specified for any other type are not required. 1.1.2?Type IAAir-entraining cement for the same uses as Type I, where air-entrainment is desired. 1.1.3?Type IIFor general use, more especially when moderate sulfate resistance is desired. 1.1.4?Type IIAAir-entraining cement for the same uses as Type II, where air-entrainment is desired. 1.1.5?Type II(MH)For general use, more especially when moderate heat of hydration and moderate sulfate resistance are desired. 1.1.6?Type II(MH)AAir-entraining cement for the same uses as Type II(MH), where air-entrainment is desired. 1.1.7?Type IIIFor use when high early strength is desired. 1.1.8?Type IIIAAir-entraining cement for the same use as Type III, where air-entrainment is desired. 1.1.9?Type IVFor use when a low heat of hydration is desired. 1.1.10?Type VFor use when high sulfate resistance is desired. Note 1:?Some cements are designated with a combined type
classification, such as Type I/II, indicating that the cement meets
the requirements of the indicated types and is being offered as
suitable for use when either type is desired.
Note 2:?Cement conforming to the requirements for all types
are not carried in stock in some areas. In advance of specifying
the use of cement other than Type I, determine whether the proposed
type of cement is or can be made available.
1.2?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3?The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
