Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM C207-18
Standard Specification for Hydrated Lime for Masonry Purposes
Translate name
STANDARD published on 1.10.2018
The information about the standard:
Designation standards: ASTM C207-18
Publication date standards: 1.10.2018
SKU: NS-904606
The number of pages: 2
Approximate weight : 6 g (0.01 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM C207-18 :
This specification covers four types of hydrated lime. Type N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to Portland-cement concrete. Types NA and SA are air-entrained hydrated limes that are suitable for use in any of the above uses where the inherent properties of lime and air-entrainment are desired. The four types of lime under this specification shall be designated as Type N which is the normal hydrated lime for masonry purposes, type S which is the special hydrated lime for masonry purposes, type NA which is the normal air-entraining hydrated lime for masonry purposes and type SA which is the special air-entraining hydrated lime for masonry purposes. Hydrated lime for masonry purposes shall conform to the required chemical composition for calcium and magnesium oxides and carbon dioxide. The hydrated lime covered by Types N or S in this specification shall contain no additives for the purpose of entraining air.
Keywords:
hydrated lime, masonry, mortar, plasticity, popping and pitting, residue, stucco, Type N, Type NA, Type S, Type SA, unhydrated oxides, water retention, air entraining ,, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Additional information
| 1. Scope | ||||||||||||||
|
1.1 This specification covers four types of hydrated lime. Types N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to portland-cement concrete. Types NA and SA are air-entrained hydrated limes that are suitable for use in any of the above uses where the inherent properties of lime and air-entrainment are desired. The four types of lime sold under this specification shall be designated as follows: 1.1.1 Type N—Normal hydrated lime for masonry purposes. 1.1.2 Type S—Special hydrated lime for masonry purposes. 1.1.3 Type NA—Normal air-entraining hydrated lime for masonry purposes. 1.1.4 Type SA—Special air-entraining hydrated lime for masonry purposes. Note 1: Type S, special hydrated lime, and Type SA, special
air-entraining hydrated lime, are differentiated from Type N,
normal hydrated lime, and Type NA, normal air-entraining hydrated
lime, principally by their ability to develop high, early
plasticity and higher water retentivity, and by a limitation on
their unhydrated oxide content.
Note 2: For normal (Type N) and special (Type S) finishing
hydrated lime, refer to Specification C206.
Note 3: Some building codes prohibit the use of air-entraining
materials in mortar, because of the accompanying reduction in bond
and compressive strength. Where increased freeze-thaw resistance is
important, air-entraining may be beneficial. Air-entraining lime
should not be used as a finishing lime.
Note 4: For lime putty, refer to Specification C1489.
1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
We recommend:
Updating of laws
Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.
