Standard Practice for Use of Rotary Kiln Produced Porous Ceramic as a Mineral Amendment in Topsoil Used for Landscaping and Related PurposesTranslate name
STANDARD published on 1.3.2019
Designation standards: ASTM D8249-19
Publication date standards: 1.3.2019
The number of pages: 3
Approximate weight : 9 g (0.02 lbs)
Country: American technical standard
Category: Technical standards ASTM
horticulture, landscaping, mineral amendment, modification, plant growth, porous ceramic, rotary kiln, soil, soil amendment, topsoil,, ICS Number Code 65.020.40 (Landscaping and silviculture)
|Significance and Use|
5.1 Landscaping and construction professionals and golf course designers are a few of the typical users of this standard. When physically evaluating a soil, relative to its suitability to support plant growth (primarily grasses), tests must be performed to determine the presence and amount of solid matter compatibility that is then used to determine potential air-void content, water-holding ability, and deleterious materials. Rotary kiln produced porous ceramic material is a mineral amendment that can be added to a topsoil to increase its suitability to support plant growth.
5.2 Typical general ranges of soil content for suitable topsoils are presented in Specification . It should be recognized, however, that in some geographic regions, concurrence with the values in the referenced table could be difficult. In such situations, locally acceptable specifications need to be developed.
Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent and objective testing/sampling/inspection/ and the like. Users of this standard are cautioned that compliance with Practice does not in itself assure reliable results. Reliable results depend on many factors; Practice provides a means of evaluating some of those factors.
1.1 This practice covers the material characteristics, physical requirements, and sampling appropriate for the designation of the rotary kiln produced porous ceramic material as a mineral amendment. The porous ceramic material can be used to replace the sand content of a topsoil or it can be blended into an existing topsoil. Typically 5-20 % by mass of porous ceramics are used when blending with or adding to a topsoil.
1.2 The potential/success of a topsoil amendment is measured/determined by its ability to provide or enhance some or all of the desired properties/characteristics of the topsoil that may be deficient in the unamended topsoil.
1.3 Soils typically consist of three components: water, air and solids. Solids can be further divided into two sub-components: organic matter, such as peat, muck or other decayed matter, and inorganic mineral matter, such as clay, silt and sand. Porous ceramic falls into the inorganic mineral matter sub-component and is generally used in horticultural topsoil applications as a substitute/alternative or addition for the sand component of soil. See Specification , Table 1.
1.4 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.
1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice , unless superseded by this test method.
1.5.1 The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.
1.6 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.
Latest update: 2021-04-20 (Number of items: 2 442 933)
© Copyright 2021 NORMSERVIS s.r.o.