Standard Test Method for Determination of Wear Metals and Contamination Elements in Used Industrial Oils by Sweeping Flat Electrode Atomic Emission SpectrometryTranslate name
STANDARD published on 1.6.2020
Designation standards: ASTM D8315-20
Publication date standards: 1.6.2020
The number of pages: 8
Approximate weight : 24 g (0.05 lbs)
Country: American technical standard
Category: Technical standards ASTM
additive elements, arc-spark emission spectrometry, concentration of non-suspendable particles, contaminants, emission spectrometry, graphite flat electrode, in-service lubricants testing, industrial oil, less populated particles, RDE, rod electrode, SFE, standardization, sweeping flat electrode, sweeping flat electrode spectrometer, wear metals, XY sweeping table,
|Significance and Use|
5.1 Used Industrial Oil—The detection of large particles are important inputs for used industrial lubricant condition mornitoring. For wear metals, these particles, in size, are represented by those between 20 μm and 50 μm in engine oil, 80 μm or greater in gear-box oil. In desert or windy areas, large sand and dust particles can enter in-service lubricant. The concentrations contributed from large particles can be more sensitive to serious or catastrophic failure of industrial equipment than those from 10 μm or less. In spectroscopic analysis, excluding large particles significantly under-reports the concentrations of wear and contamination elements. The corresponding results may not represent the actual state of in-service lubricant. Because this test method posts less limitation on the size of wear metal particles while still reporting normal fine wear particles, it provides a means to assess wear and contamination elements in a comprehensive range of the size of particulates and raises the fidelity of spectroscopic analysis of in-service lubricant.
5.2 Non-suspendable Particles in Used Industrial Oil—The increase of non-suspendable particles suggests excessive wear or poor sealing of machinery, or both. Large amounts of such particulate in industrial oil bulk itself are harmful to moving parts of machinery. This test method provides another means to identify the presence or absence of the non-suspendable particles for machinery condition monitoring.
1.1 This test method covers the determination of wear metals and contaminants in used industrial oils by sweeping flat electrode atomic emission spectroscopy (SFE-AES).1.2 Industrial oil includes lubricant oil, gear box oil, hydraulic fluid, compressor oil, turbine oil, synthetic oils, and other petroleum oils.
1.3 Method working range for every element is evaluated by equations in and tabulated in Table 6.
1.4 Though this technique is designed to analyze non-suspended particles in lubricant samples, the precision statements published here were established solely from homogeneous oil samples per Practice requirements. Non-suspended particles, which are inhomogeneous by nature, were not sampled and evaluated for deriving precision statements for this test method (see ).
1.5 This test method provides a quick indication for abnormal wear and the presence of contamination in new or used industrial oils by immediately reporting:
1.5.1 Normal fine particles of specific wear metals;
1.5.2 Non-suspendable particles of specific wear metals and of contamination elements;
1.5.3 Less populated large particles (10 μm to 50 μm) of specific wear metals;
1.5.4 Contamination elements; and
1.5.5 Additive elements.
1.6 This test method uses oil-soluble elements for calibration and does not purport to relate quantitatively the values determined as insoluble particles to the dissolved metals. Analytical results are particle size dependent and low results may be obtained for those elements present in used oil samples as large particles (referenced by Test Methods and ).
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Latest update: 2021-04-13 (Number of items: 2 440 761)
© Copyright 2021 NORMSERVIS s.r.o.