We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
Standard Test Method for Determining Enhanced Filter Blocking Tendency (EFBT)Translate name
STANDARD published on 1.4.2021
Designation standards: ASTM D8386-21
Publication date standards: 1.4.2021
The number of pages: 8
Approximate weight : 24 g (0.05 lbs)
Country: American technical standard
Category: Technical standards ASTM
automotive diesel, filter blocking tendency (EFBT), filterability, gas oil, marine diesel, middle distillates,
|Significance and Use|
5.1This test method is intended for use in evaluating the cleanliness of middle distillate fuels for quality control purposes.
5.2The filter media specified in this procedure is suitable for the materials in the scope.
5.3A change in filtration performance after storage or pretreatment can be indicative of changes of fuel condition.
5.4The filterability of fuels varies depending on filter porosity and structure. Therefore, results from this test method might not correlate with full-scale filtration; however, results from this test might help identify fuels that can reduce filter life.
5.5 Causes of poor filterability in industrial/refinery filters include fuel degradation products, contaminants (including water) picked up during storage or transfer, effects due to temperature or composition for diesel, incompatibility of commingled fuels, or interaction of the fuel with the filter media. Any of these could correlate with orifice or filter system plugging, or both.
5.6 The results of the EFBT test can range from 1 for a fuel with very good filterability, to over 30 for a fuel with poor filterability. The selection of a single EFBT number to define a pass or fail criteria is not possible, as this will be dependent on the fuel type and application specifics. The correlation between filter life and EFBT number is, therefore, dependent on many variables stemming from the design and use of the engine. Some factors like pressures and particle size removal required come from the fuel system design while others are a result of the duty cycle and environment where the engine is deployed. As an example, a large displacement HPCR (High-Pressure Common Rail) engine in continuous operation may have cleanliness needs much greater than that of a medium or light-duty engine in occasional use. In each case, the expected EFBT value may be different. An EFBT value of <1.4 for the fuel before it reaches the fuel system in the first example of HPCR engines may be suitable, while an EFBT <2.0 may be suitable in the medium/light-duty engines. In a small study, the EFBT test was shown to be more sensitive to constituents in the fuel than the Test Method method ( ).
1.1This test method covers a procedure for the determination of the Enhanced Filter Blocking Tendency (EFBT) and the filterability of middle distillate fuel oils. This test is applicable to fuels within the viscosity range of 1.3mm2/s to 6.0mm2/s at 40C.
Note 1:ASTM specification fuels falling within the scope of this test method are: Specification Grades No 1 and 2; Specification Grades No. 1-D S15 and S500, and No. 2-D S15 and S500; Specification Grades No. 1-GT and No. 2-GT.
1.2This test method has interim repeatability only. For more information, see Section .
1.3This test method is not applicable to fuels that contain free (undissolved) water (see ).
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
Latest update: 2022-11-28 (Number of items: 2 642 990)
© Copyright 2022 NORMSERVIS s.r.o.