Standard Quantitative Disk Carrier Test Method for Determining Bactericidal, Virucidal, Fungicidal, Mycobactericidal, and Sporicidal Activities of Chemicals (Includes all amendments and changes 1/22/2018).Translate name
STANDARD published on 1.12.2017
Designation standards: ASTM E2197-17e1
Publication date standards: 1.12.2017
The number of pages: 13
Approximate weight : 39 g (0.09 lbs)
Country: American technical standard
Category: Technical standards ASTM
adenovirus, Aspergillus niger conidia, Bacillus subtilis spores, bactericides, calicivirus, Candida albicans, cell cultures, chemical microbicides, Clostridium sporogenes spores, eluate, eluent, environmental surfaces, fungicides, hepatitis A virus, medical devices, membrane filtration, mycobactericides, Mycobacterium terrae, norovirus, parvovirus, Pseudomonas aeruginosa, quantitative carrier test, rhinovirus, rotavirus, soil load, sporicides, Staphylococcus aureus, standard hard water
|Significance and Use|
5.1 The design of this test eliminates any loss of viable organisms through wash off, thus making it possible to produce statistically valid data using many fewer test carriers than needed for methods based on simple MPN estimates.
5.2 The stringency in the test is provided by the use of a soil load, the microtopography of the brushed stainless steel carrier surface, and the smaller ratio of test substance to surface area typical for many disinfectant applications. Thus, the test substance being assessed is presented with a reasonable challenge while allowing for efficient recovery of the test organisms from the inoculated carriers. The metal disks in the basic test are also compatible with a wide variety of actives.
5.3 The design of the carriers makes it possible to place onto each a precisely measured volume of the test organism (10 μL) as well as the control fluid or test substance (50 μL).
5.4 The inoculum is placed at the center of each disk whereas the volumes of the test substance covers nearly the entire disk surface, thus virtually eliminating the risk of any organisms remaining unexposed.
5.5 In all tests, other than those against viruses, the addition of 10 mL of an eluent/diluent gives a 1:200 dilution of the test substance immediately at the end of the contact time. While this step in itself may be sufficient to arrest the microbicidal activity of most actives, the test protocol permits the addition of a specific neutralizer to the eluent/diluent, if required. Except for viruses, the membrane filtration step also allows processing of the entire eluate from the test carriers and, therefore, the capture and subsequent detection of even low numbers of viable organisms that may be present. Subsequent rinsing of the membrane filters with saline also reduces the risk of carrying any inhibitory residues over to the recovery medium. Validation of the process of neutralization of the test substance is required by challenge with low numbers of the test organism.
5.6 In tests against viruses, addition of 1 mL of buffer at the end of the contact time achieves a 1:20 dilution of the test substance while keeping the volume of the eluate reasonably small to allow for the titration of most or all of the eluate in cell cultures. Confirmation of neutralization of the test substance is required by challenge of a residual disinfection load with low numbers of infective units of the test virus. Since the virus assay system is indirect, an additional step is required to demonstrate that prior exposure of the appropriate cell line to any residual disinfectant or disinfectant/neutralizer mixture does not interfere with the detection of a low level of virus challenge (See Appendix).
Note 1: In and , volumes of 10 mL and 1 mL are recommended instead of 9.95 mL and 950 μL, respectively, for ease of dispensing the eluent.
5.7 The soil load in this test is a mixture of three types of proteins (high molecular weight proteins, low molecular weight peptides, and mucous material) designed to represent body secretions, excretions, or other extraneous substances that microbicidal chemicals may encounter under field conditions. It is suitable for working with all types of test organisms included here. The components of the soil load are readily available and subject to much less variability than animal sera.
5.8 If distilled water or other diluent is not to be specified on the product label, the diluent for the test substance is assumed to be tap water. Since the quality of tap water varies considerably both geographically and temporally, this test method incorporates the use of water with a specified and documented level of hardness to prepare use-dilutions of test substance that require dilution in water before use. While water with a hardness of at least 300 ppm as CaCO3 is recommended consult local regulations regarding use of hard water prior to testing.
5.9 The Annex contains a list of those organisms that are often used in assessing the microbicidal activities of disinfectants for use on environmental surfaces or medical devices. Culture conditions for each organism are also included in the Annex. Depending on the label claim(s) desired and the requirements of the target regulatory agency, one or more of the organisms listed may be selected for the testing. If organisms other than those listed are to be used (for example, in the dairy or brewing industries), a clear justification must be provided and details of the culture media and growth conditions must be validated and clearly specified in test reports.
1.1 This test method is designed to evaluate the ability of test substances to inactivate vegetative bacteria, viruses, fungi, mycobacteria, and bacterial spores 1.2 The test protocol does not include any wiping or rubbing action. It is, therefore, not designed for testing wipes.
1.3 This test method should be performed by persons with training in microbiology in facilities designed and equipped for work with infectious agents at the appropriate biosafety level 1.4 It is the responsibility of the investigator to determine whether Good Laboratory Practice Regulations (GLPs) are required and to follow them where appropriate (40 CFR, Part 160 for EPA submissions and 21 CFR, Part 58 for FDA submissions).
1.5 In this test method, SI units are used for all applications, except for distance in which case inches are used and metric units follow.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
Latest update: 2021-04-12 (Number of items: 2 440 772)
© Copyright 2021 NORMSERVIS s.r.o.