Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM F1545-15a(2021)
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges (Includes all amendments and changes 10/22/2021).
Translate name
STANDARD published on 1.7.2021
The information about the standard:
Designation standards: ASTM F1545-15a(2021)
Publication date standards: 1.7.2021
SKU: NS-1040620
The number of pages: 9
Approximate weight : 27 g (0.06 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM F1545-15a(2021) :
This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges for conveying corrosive fluids. Lining material shall be made from a resin that conforms to the requirements of this specification. Other requirements include mechanical properties, specific gravity, finish, dimensions, design, working pressure, working temperature, flange construction, venting, workmanship, performance, quality, marking, and packaging. High-temperature test, low-temperature test, steam-cold water cycling test, vacuum test, hydrostatic pressure test, and electrostatic test shall be done in accordance to the procedures of this specification.
Keywords:
plastic-lined ferrous metal fittings, plastic-lined ferrous metal flanges, plastic-lined ferrous metal pipe ,, ICS Number Code 23.040.10 (Iron and steel pipes),23.040.20 (Plastic pipes)
Additional information
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included. 1.1.1?This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer's chemical resistance data for suitability recommendations. 1.1.2?This specification does not include products coated with plastics. 1.2?This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner. Note 1:?In this specification, propylene plastics cover those
materials defined as both polypropylene plastics and propylene
plastics in Terminology F412.
Both materials are identified as PP on the product. Note that this
is at variance with Terminology D1600, where PP is the abbreviation for
polypropylene.
1.3?The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum. Note 2:?The temperature limitations are based on noncorrosive
test conditions. Use in specific aggressive environments may alter
temperature limitations. In such instances, specific temperature
limits shall be established by mutual agreement between the
purchaser and the manufacturer.
1.4?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
We recommend:
Updating of laws
Do you want to be sure about the validity of used regulations?
We offer you a solution so that you could use valid and updated legislative regulations.
Would you like to get more information? Look at this page.
