Cookies
We need your consent to use the individual data so that you can see information about your interests, among other things. Click "OK" to give your consent.
ASTM F1667-15
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
STANDARD published on 1.9.2015
The information about the standard:
Designation standards: ASTM F1667-15
Note: WITHDRAWN
Publication date standards: 1.9.2015
SKU: NS-618478
The number of pages: 47
Approximate weight : 141 g (0.31 lbs)
Country: American technical standard
Category: Technical standards ASTM
The category - similar standards:
Annotation of standard text ASTM F1667-15 :
Keywords:
diameter, driven fasteners, head, length, nails, point, spikes, staples,, ICS Number Code 21.060.01 (Fasteners in general)
Additional information
| 1. Scope | ||
|
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 1: Fastener ductility information is presented in
Table 2 and dimensional
information in Tables 3–65.
† Editorially corrected in March
2012.
L
|
= |
length, in., |
|
H |
= |
head diameter, in., |
|
TL |
= |
length of threaded shank, in., |
|
max |
= |
maximum acceptable value (not subject to tolerances), |
|
min |
= |
minimum acceptable value (not subject to tolerances), |
|
D |
= |
shank diameter, in., |
|
T1 |
= |
crest diameter, in., and |
|
P |
= |
pitch, or spacing of threads, in. |
L
=
length, in.,
H
=
head diameter, in.,
TL
=
length of threaded shank, in.,
max
=
maximum acceptable value (not subject to tolerances),
min
=
minimum acceptable value (not subject to tolerances),
D
=
shank diameter, in.,
T1
=
crest diameter, in., and
P
=
pitch, or spacing of threads, in.
Dimensions and Tolerances for Gages of Flat Top Crown Staples
10 Gage
12 Gage
14 Gage
15 Gage
16 Gage
18 Gage
T
W
T
W
T
W
T
W
T
W
T
W
Nominal
.1250
.1400
.0935
.1120
.0735
.0855
.0673
.073
.0563
.064
.038
.050
Maximum
.1290
.1440
.0975
.1160
.0775
.0895
.0731
.076
.0626
.068
.0415
.0532
Minimum
.1210
.1360
.0895
.1080
.0695
.0815
.0615
.070
.0500
.060
.0345
.0468
Tolerance
±
.0040
.0040
.0040
.0040
.0040
.0040
.0058
.003
.0063
.004
.0035
.0032
1.2 Fasteners described in this
specification are driven by hand tool, power tool, or mechanical
device in single or multiple strikes and are positioned by hand,
tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
Standard Test Methods for Nails |
|
|
Standard Test Method for Determining Bending Yield Moment of Nails |
|
|
Standard Terminology of Collated and Cohered Fasteners and Their Application Tools |
|
|
Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
|
|
Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel [Metric] (Withdrawn 2011) |
|
|
Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire |
|
|
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
|
|
Standard Terminology of Nails for Use with Wood and Wood-Base Materials |
We recommend:
Technical standards updating
Do you want to make sure you use only the valid technical standards?
We can offer you a solution which will provide you a monthly overview concerning the updating of standards which you use.
Would you like to know more? Look at this page.
